Put the classic 8-Way Eurojoystick fighting joystick in a portable fightstick with this detachable shaft version!

*NEW* Sanwa Joystick JLX-TP-8YT with dust washers only, no top or harness.

*NEW* Sanwa Joystick JLX-TPML-8YT with adjustable silent leaf switches. Includes dust washers only, no top or harness.

This restrictor plate has 8 corners to easily make smooth and precise combination moves in fighting games. For use on the Sanwa JLF & JLX joysticks. This item is a replacement for the older GT-Y restrictor plate. Functionally there is no difference, the primary change is how the yellow insert mounts into the clear housing.

This round restrictor plate has a circular center for smooth 360-degree movement of the joystick. For use on the Sanwa JLF & JLX joysticks.

This restrictor plate has rounded corners but still has small ridges to provide defined movements to each of the 8 directions. For use on the Sanwa JLF & JLX joysticks.

This restrictor plate has rounded corners but what makes it unique is the top and bottom are smooth (no ridges like the Type 1 GTX-R) but it still has ridges on the left and ride sides, so when used with fighting games you still have defined locations for left/right movement but smooth rotation at the top/bottom. Note: Of course it can be installed in different directions, so if it does not work as expected be sure to check the rotating of the inner ring to put the corner and ridges where you want them. For use on the Sanwa JLF & JLX joysticks.

Sanwa Joystick JLFD-TP-8YT with detachable joystick shaft for portable arcades and fight sticks. Includes dust washers only, no top or harness.

This is the latest silent joystick by Sanwa, with their higher tension spring, upgraded restrictor plate, and Omron D2RV-G-SD3 reed switches for almost silent operation.

Connect to PacLED64 or I-PAC Ultimate I/O Board.

Sanwa Joystick JLW-TM-8 with dust washer only, no top included.

15mm (19/32in) long shaft extension for 9mm wide joysticks shafts. Fits Sanwa, Ultimarc, Zippyy, and others with metal shafts with M6-1.0 thread.

Mount your joystick from under the control panel with no visible hardware using this kit. Contains 1/2" screws for joysticks with metal mounting plates such as Sanwa and Zippyy.

Mount your joystick from under the control panel with no visible hardware using this kit. Contains 3/4" screws for joysticks with thick plastic mounting plates such as Industrias Lorenzo and Suzo Happ.

Easily add a Sanwa, Zippy, or other joystick to a Ms Pac Man control panel with this 16 gauge steel adapter plate.

Easily add a variety of joysticks to a control panel with Suzo Happ / Industrias Lorenzo (IL) joystick mounting holes.

Sanwa Joystick JLF-TP-8YT with dust washers only, no top or harness. **Replaced by new Sanwa JLX Joystick**

White LEDs light up both the shaft and the ball top! Now with translucent dust cover so it lights up too!

Switch between 4-way & 8-way from the top of the control panel!

This restrictor plate has 8 corners to more easily make smooth and precise combination moves in fighting games, instead of using a regular 8-way gate. For use on the Sanwa JLF-TP-8YT joystick.

This restrictor plate is limited to 2 directions, allowing only Left/Right or Up/Down movement depending on which direction you install the gate. For use on the Sanwa JLF-TP-8YT joystick.

This restrictor plate comes on all Sanwa JLF-TP-8YT joysticks by default but is available here in case you need a replacement. You can adjust it for 4 or 8 players by rotating the insert 45 degrees. For use on the Sanwa JLF-TP-8YT joystick.

Slightly smaller than the Medium adapter plate, this allows you to easily add a variety of joysticks to a control panel with Suzo Happ / Industrias Lorenzo (IL) joystick mounting holes.

Switch between 4-way & 8-way from the top of the control panel!

For use with Suzo Happ Super Joystick or similar that requires 1" lever actuator switches.

Generic version of the Sanwa JLW-TM-8 joystick with a rotating restrictor plate. Includes dust washer.

Pink LEDs light up both the shaft and the ball top! Now with translucent dust cover so it lights up too!

The Ultrastik software controls the mode of the joystick, but you can add a physical 4/8-way or circular limit with this kit.

The Ultrastik software controls the mode of the joystick, but you can add a physical octagonal limit with this kit.

Harder than than the stock spring, this causes the joystick to have stiffer movement.

Switch between 4-way & 8-way from the top of the control panel!

12-Way Rotary Joystick Upgrade for the Ultimarc J-Stik (Sanwa JLW-TM-8) and Ultimarc Servostik joysticks.

Replacement joystick shaft for the Ultimarc Ultrastik 360 that is 10mm longer. Also fits the Ultimarc J-Stik, ServoStik and Sanwa JLW-TM-8.

Ultimarc J-Stik with dust washer only, no top included.

Add a high-res 1200 pulse-per-rev spinner (same as the Spintrak) to an Ultimarc 360 Joystick